Z-V型雷電計數器校驗儀
1. 電壓:DC 900V 1200V 1600V三檔
2. 放電電流>100A/10US

Z-V型雷電計數器校驗儀
二. 使用方法
.1.使用前先充電,為確保充電效果和延長電池使用壽命,需使用專配的充電器.空電池到充滿需3-4小時,充電器上紅燈亮表示正在充電;綠燈表示充電完畢.使用前在尾端插接好所附地線插頭,地線夾接大地.
2.根據計數器安裝高度,適當拉出伸縮放電桿.
3.按下紅色按鈕,接通高壓約1秒鐘,指示燈亮(微閃),即可輕輕點擊計數器與避雷器的連接端進行測試.
4.每次點擊后,放電桿端頭應離開計數器.若需重復測試,可不必松開按鈕,約過,1-2秒鐘指示燈再次閃爍時,即可再次點擊測試.
5.連續測試會導致檢驗儀發熱,請注意適當間歇時間.
6.如按下按鈕3秒鐘以上指示燈仍未閃亮,則表示需對電池進行充電.
7.校驗儀請勿隨意拆卸.如電池容量明顯下降或充電效率過低,則需要換,請向本公司購買專用電池組.
Z-V型雷電計數器校驗儀
注意:指示燈亮(微閃)時身體的任何部位均不能碰觸電極部分,否則有電擊危險